Startseite / Blog & Ratgeber / CNC Machining

CNC Surface Finish Ra Chart: What Each Roughness Level Costs

Published 2026-11-12 · 8 min read

SkillsProto machines to ±0.005 mm on critical features and finishes most parts to Ra 3.2 or 1.6 micrometres inside the standard 3-7 day window, which covers the vast majority of functional CNC parts. Tighter than Ra 0.8 stops being a machining question and becomes a grinding, honing or lapping question, with a different supplier, a different price and a longer lead time. This chart maps each level to the operation that produces it, so the callout on your drawing matches something a machine shop can actually hold.

CNC milling cutter removing metal from a fixtured workpiece
CNC milling of a fixtured workpiece. Cutting strategy, fixturing and tool access drive both tolerance and cost.

The Ra chart

Ra (micrometres)Ra (microinches)How it is producedTypical processRelative cost indexTypical application
12.5500Roughing passes, visible tool marksRough milling100Non-functional clearance faces, hidden pockets
6.3250Standard roughing to semi-finishingMilling, turning105General machined surfaces, brackets
3.2125Normal finishing pass, sharp insertMilling, turning110Default functional finish, most prototype parts
1.663Light finishing pass, higher speed, wiper insertMilling, turning125Sealing faces, sliding contact, mating surfaces
0.832Fine finishing, small stepover, or grindingFine milling, surface grinding150-180Bearing seats, hydraulic sealing faces
0.416Grinding, honingGrinding220-280Precision bores, valve seats, gauge surfaces
0.28Fine grinding, lappingGrinding, lapping350+Optical and metrology reference faces
0.052Lapping, polishingLapping, polishing500+Mirror surfaces, seal faces in vacuum service

The cost index is relative to a rough-machined face on the same part, not a price list. The important shape is that the curve is flat between 12.5 and 3.2, and steep after 0.8, because at that point you change process rather than change a feed rate.

What actually sets the number

Ra is not a dial on the machine. It is the result of four things, and only the first is a choice.

Tool nose radius and geometry. A larger nose radius at the same feed leaves a shallower scallop. This is why a wiper insert can hit 1.6 on a face where a sharp finishing insert struggles.

Feed per revolution or per tooth. Roughness rises with the square of feed in the theoretical model, which is why halving the feed improves finish far less than proportionally while doubling the time.

Cutting speed and stability. Chatter is the enemy of finish. A long tool, a thin wall or an insufficiently rigid setup will produce a worse surface at any feed, and no amount of polishing the program fixes a vibrating setup. This is the reason a tall thin rib machines to a worse finish than a solid block, even with identical parameters.

Material. Aluminium finishes easily and 6061-T6 takes a near-mirror with a sharp cutter. Stainless 304 work-hardens and smears, tool steel needs slower speeds, and titanium is its own discipline. The same callout on a different alloy can move the achievable finish by two grades.

Ra is not Rz, and the drawing should say which

Ra is the arithmetic mean deviation of the profile over the sampling length; Rz is the maximum height of the profile within it. A surface can meet Ra 3.2 and still have isolated peaks that damage a seal, because Ra averages them away.

ParameterWhat it measuresWhen to specify it
RaAverage roughness across the profileGeneral machining and most functional faces
RzPeak-to-valley height in the sampling lengthSealing faces, where peaks matter more than the average
RmaxSingle worst peak in the evaluation lengthCritical sealing and wear surfaces
RtTotal height over the full evaluation lengthSpecification disputes, surface acceptance

For most machined parts Ra alone is enough. For a face that seals against an O-ring or a gasket, specify Rz or Rmax as well, because the peaks are what leak.

The cost of a blanket callout

A note that says "all surfaces Ra 0.8" is the most common way to inflate a CNC quote without gaining anything. It converts every non-functional face into a fine-finishing operation, forces small stepovers across the whole part, and in many cases pushes the job into a second process because some faces cannot be reached to that finish at all.

The fix is a default plus exceptions: ISO 2768-m general tolerance with Ra 3.2 as the general finish, then specific callouts only on the faces that seal, slide, mate or locate. On a typical bracket this removes most of the fine finishing time and none of the function.

Three callouts that pay for themselves:

  • Name the datum and the face. "Ra 0.8 on the sealing face, 20 mm diameter, both sides" is checkable. "Good finish on sealing surfaces" is not.
  • Say whether machining marks may run in one direction. On a sliding or sealing face the lay direction matters and costs nothing to specify.
  • Separate cosmetic from functional. A visible anodised cover can be bead blasted for appearance at a fraction of the cost of finishing it to 0.8.

What finishing does to the number

Machining sets the geometry of the surface; finishing changes it.

FinishEffect on RaEffect on tolerance
As-machinedNone, it is the baselineNone
Bead blastSlightly roughens fine surfaces, hides tool marksMinimal, edge break only
Anodise, clearBuilds roughly 5-15 micrometres, follows the substrateCan shift tight tolerances, mask critical features
Hard anodiseBuilds more, and the oxide is harder than the baseMask bores and threads, or finish after anodising
PassivationChemical clean, no dimensional changeNone
ElectropolishSmooths peaks, improves Ra by a grade or twoRemoves material, typically a few micrometres

Anodising is the trap: a part finished to Ra 0.4 and then hard anodised without masking the bore is no longer a Ra 0.4 bore at the specified diameter. Mask, or finish after coating.

How to inspect it without arguing

Ra is measured with a stylus profilometer over a stated cutoff length, in a stated direction, at a stated position. If the drawing does not state those, two people can measure the same face and disagree.

For prototype quantities, a comparison comparator plate is usually enough for 12.5 to 3.2, and a profilometer is needed from 1.6 down. SkillsProto reports measured values on request for critical faces and includes them in the inspection record, which matters more than the number itself when a customer is auditing the part.

Getting a finish quoted

Send the STEP file with the finish callouts on the faces that matter to /quote/. SkillsProto returns DFM notes and a price in 24 hours, machines to ±0.005 mm on critical features, finishes to Ra 3.2 or 1.6 as standard with tighter levels quoted explicitly, ships MOQ 1 in 3-7 days, and delivers DDP in 3-5 days.

Frequently Asked Questions

What surface finish can CNC machining achieve?

Standard milling and turning reach Ra 3.2 easily and Ra 1.6 with a light finishing pass. Ra 0.8 is achievable by fine milling on accessible faces or by surface grinding, and below that grinding, honing or lapping takes over. A shop that quotes Ra 0.4 on a milling operation alone is usually describing a grinding operation with milling in front of it.

Is Ra 1.6 better than Ra 3.2?

Better only if the function needs it. Ra 1.6 costs more because it needs a lighter finishing pass or a wiper insert, and it buys lower friction, better sealing or a finer appearance. On a bracket face that carries no seal and no sliding contact, Ra 3.2 performs identically and costs less.

How much does a tighter surface finish add to the price?

Between Ra 12.5 and Ra 3.2 the difference is small, often under 10% of the part price, because it is a finishing pass on the same setup. From Ra 1.6 to 0.8 the cost steps up as feeds drop, and below 0.8 the process changes to grinding, which typically adds 50-100% or more depending on how many faces are called out.

What is the difference between Ra and Rz?

Ra is the average deviation of the surface profile; Rz is the peak-to-valley height within the sampling length. A surface can pass Ra 3.2 while containing peaks tall enough to breach a seal, which is why sealing faces are specified in Rz or Rmax rather than Ra alone.

Why did my quote go up when I added a finish note?

Almost always because the note applied to every face rather than the faces that function. A blanket Ra 0.8 callout forces fine finishing across the whole part, adds stepover time and often forces a second operation for faces that cannot be reached. A default of Ra 3.2 with named exceptions usually brings the price back.

Does anodising change the surface finish value?

It changes the surface the customer receives. Anodising builds an oxide layer that follows the substrate, so a 3.2 surface stays visually similar but the measured Ra shifts, and tight bores and threads grow by microns. Hard anodise builds more and is usually specified with masking on precision features or applied before final finishing.

Related capabilities

Related guides

Have parts to quote?

Upload your files — DFM-checked quotation within 24 hours.

Angebot anfordern