कॉन्सेप्ट से तैयार पार्ट तक — ISO 9001 निर्माता · 24 घंटे में कोटेशनमुफ़्त कोटेशन पाएँ →

Machined vs Extruded Heat Sink Profiles: When CNC Wins

Published 2026-11-09 · 9 min read

SkillsProto machines heat sinks from solid aluminium plate at MOQ 1 with 3-7 day delivery, and that is the correct route whenever an extruded profile cannot deliver the fin geometry, base flatness or mounting features your thermal design needs. Extrusion wins on cost per part once you are buying the same standard profile in four figures. Machining wins below that, and on anything with variable fin pitch, pin fins, pockets or a machined thermal pedestal. The break-even is arithmetic, not a matter of supplier preference.

The decision is tooling against per-part cost, and nothing else

An extruded heat sink is a die with a hole in it. You pay for the die once, then buy metal by the metre. A machined heat sink is machine time per part with no die at all. Every argument about fins, finishes and lead times reduces to those two cost structures put side by side at your quantity.

That is why "which is better" has no answer and "which is better at 40 pieces" does.

What an extruded profile can and cannot do

Extrusion pushes hot billet through a die, so the cross-section must be constant along the length. That single constraint decides most of the arguments:

  • Constant cross-section only. Straight fins running the full length, a flat base, maybe a pair of T-slots on the underside. Any pocket, boss, stepped base or isolated pedestal becomes a second machining operation.
  • Minimum fin thickness and aspect ratio. A die needs metal to flow and a mandrel to survive. Practical extruded fins get thin, but not as thin as a milled fin, and deep narrow gaps are the first thing a die maker pushes back on.
  • Alloy limited to what extrudes well. 6063 is the default because it flows and finishes well; it conducts at roughly 209 W/m-K. 6061 conducts at roughly 167 W/m-K and is harder to extrude into thin fins. Copper is not an extrusion option for this application at all.
  • Base flatness is a mill finish, not a thermal interface. An extrusion comes off the press and gets straightened. If your thermal path depends on 0.02 mm of base flatness over a 40 mm footprint, the profile will be machined on the base anyway.
  • Length is free. Cutting a profile to length costs almost nothing, which is why long linear LED rails are almost always extruded.

What machining buys you

A machined heat sink starts as plate and removes everything that is not a heat sink. SkillsProto mills fins, pin arrays, pockets and mounting patterns from one setup family, holding ±0.005 mm on critical features and ISO 2768-m elsewhere.

The four things that make teams choose machining over extrusion:

1. Geometry freedom. Variable fin pitch, interrupted fins, pin fin arrays, a raised pedestal directly under the die, mounting bosses, connector cut-outs, and a base that steps to clear components on the PCB.

2. A base you can trust as a thermal interface. The base is machined flat and can be specified to a flatness and roughness the interface material actually needs, rather than to whatever the press produced.

3. No tooling and no minimum. MOQ is 1. A design iteration costs a new STEP file and another 3-7 days, not a new die.

4. Material choice. 6061-T6, 7075, 6082 or copper, selected on conductivity, weight or machinability rather than on what extrudes.

AttributeExtruded profileCNC machined
ToolingDie, paid onceNone
Economic quantityHigh volume, one profile1 to a few thousand
Cross-sectionConstant along lengthAny geometry
Fin aspect ratioDie-limitedTool reach and stiffness limited
Base flatnessMill tolerance, usually re-machinedMachined to callout
Alloy range6063, some 60616061, 7075, 6082, copper
Typical lead timeWeeks for a new die, days for stock profile3-7 days
Design change costNew die or secondary machiningNew model
Best fitLED linear, standard footprints, high volumeElectronics prototypes, non-linear layouts, low volume

The break-even, worked

Take a heat sink 100 mm x 60 mm with a 6 mm base and eleven straight fins, which is a shape that extrudes comfortably. Assume an extrusion die in the low thousands of dollars, a per-metre profile price that makes each 100 mm part cost a few dollars, and a machined part that costs several times that because a 100 x 60 x 25 mm block of 6061 has to be roughed out.

QuantityExtruded, relative total costMachined, relative total costCheaper route
1100 (die dominates)3Machined
253412Machined
1001445Machined
5006220Extruded
2,0004880Extruded
20,00048,800Extruded

The numbers are an index, not a quotation, but the shape is universal: the die is a fixed cost that a machined part does not have, and machine time is a variable cost that an extrusion barely has. The crossover in this example sits somewhere between 100 and 500 pieces, and it moves with fin count, base thickness and how much secondary machining the extrusion needs to become a finished part.

Two adjustments push the crossover upward, which is where most electronics projects actually live: if the profile must then be faced, drilled and tapped, part of the machining cost returns to the extrusion, and if the design needs pin fins or a stepped base, no extrusion exists at any volume.

Thermal performance is not automatically better on either route

Neither process is thermally superior in principle. Both make aluminium fins with a base, and the thermal resistance is set by the same physics: spreading resistance in the base, fin efficiency along the fin, the convection coefficient the airflow supports, and the interface between the base and the source.

What differs is the range of geometries you can reach. An extrusion locks you into one fin pitch and one fin height along the whole length. If your heat source is a single 15 mm die in the middle of a 100 mm base, a machined heat sink lets you put dense fins over the die and coarse fins at the ends, thicken the base under the source to spread heat, and leave the rest of the plate thin. That is a real thermal gain, not a cosmetic one, and it is available only where the geometry is free.

The other real difference is the interface. A machined base can be specified flat and at a controlled roughness so a thin thermal pad does its job; an extrusion that nobody faces gives you whatever the profile gives you, and that interface resistance is usually the largest single term in the stack at prototype quantities.

The hybrid most teams should consider

The pragmatic answer for a product that will eventually run in the thousands but is at 50 today is a hybrid: buy or specify the extruded profile for the thermal body, and machine only the interface features, which means facing the base, drilling and tapping the mounting pattern, and cutting pockets for components.

That keeps the die investment for the volume phase, gives you a working part in 3-7 days, and defers the die decision until the design stops moving. SkillsProto machines the secondary operations on supplied or specified profiles as well as complete heat sinks from solid, so the two routes are not mutually exclusive.

A checklist before you commit to a route

  • Does the cross-section stay constant along the full length? If not, machining.
  • Is the annual quantity above roughly 1,000 of one identical part? If not, machining.
  • Do you need fin pitch variation, pin fins, or a pedestal under the source? If yes, machining.
  • Does the base need a flatness callout for a thermal interface? Add a facing operation either way.
  • Is the design still moving? Machining, because a change costs a model rather than a die.
  • Is the part longer than about 300 mm and linear? Extrusion is hard to beat.

Getting a machined heat sink quoted

Send the STEP file with the fin geometry, the base flatness callout and the mounting pattern to /quote/. SkillsProto returns DFM notes and a price within 24 hours, machines from 6061, 7075, 6082 or copper to ±0.005 mm on critical features, ships MOQ 1 in 3-7 days, and delivers DDP in 3-5 days. If an extrusion is the better route at your volume, say so in the request and the quote will tell you which routes were compared.

Frequently Asked Questions

At what volume is an extruded heat sink cheaper than a machined one?

It depends on the die cost and on how much secondary machining the profile needs, but the crossover usually sits between 100 and 500 identical parts for a simple straight-fin profile, and later if the extrusion has to be faced, drilled and tapped. Below that range, machining is cheaper because there is no die to amortise.

Can CNC machining make thinner fins than extrusion?

Yes. An extrusion is limited by die strength and metal flow, and deep narrow gaps are the first feature a die maker rejects. A machined fin is limited by tool reach and stiffness instead, so a milled fin can be thinner and the gap between fins can be narrower than an extruded profile allows, at the cost of more machine time per part.

Is a machined heat sink thermally better than an extruded one?

Not automatically. Both are aluminium fins on a base and obey the same thermal equations. Machining is better when the geometry needs to vary across the part, for example denser fins over the die and a thicker base under the source, or when the base needs a flatness callout for a thin thermal interface. For a uniform linear profile, extrusion performs the same.

Which aluminium alloy should a machined heat sink use?

6061-T6 is the default for machined heat sinks: it machines cleanly, anodises well and conducts at roughly 167 W/m-K. 6063 conducts at roughly 209 W/m-K and is the extrusion alloy, but it is softer and gummier to machine. Copper at roughly 401 W/m-K is used when the thermal budget cannot be met in aluminium and the weight penalty is acceptable.

How long does a machined heat sink take compared with an extruded one?

A machined heat sink ships in 3-7 days from a released model, with a 48-hour expedite on simple geometry. An existing extruded profile can also ship in days, but a new die is a tooling project measured in weeks. That asymmetry is the main reason prototype heat sinks are machined and production heat sinks are extruded.

Can you machine an extruded profile after extrusion?

Yes, and it is the usual hybrid route: the profile provides the fin body and the machine shop faces the base, drills and taps the mounting pattern and cuts component pockets. Doing so restores the base flatness an extrusion does not guarantee and adds the features a constant cross-section cannot produce, without paying for a new die.

Related capabilities

Related guides

Have parts to quote?

Upload your files — DFM-checked quotation within 24 hours.

कोटेशन पाएं