Heat Sink Prototype Cost and Lead Time: What Drives Both

Published 2026-11-10 · 9 min read

SkillsProto prices a machined heat sink prototype from a STEP file within 24 hours and ships it in 3-7 days at MOQ 1, which for one to fifty parts is almost always the fastest and cheapest route to a part you can test. The price is set by machining time, and machining time is set by fin count, fin depth and how much material has to be removed from the base. Lead time is set by finishing and material stock, not by the machining itself.

The cost stack, in the order it accumulates

A heat sink prototype quote is five lines added together, and only one of them is the metal.

Cost lineShare of a typical prototype quoteWhat moves it
Material10-25%Alloy, block size, how much is removed as chips
Programming and setup10-20%Number of setups, fixture, 3-axis versus 5-axis
Machining time40-60%Fin count, fin depth, fin thickness, base removal
Finishing5-15%As-machined, bead blast, anodise, mask and chem film
Inspection and packing3-8%First article report, CMM, flatness measurement
Freight, DDPQuoted separately or inside DDP priceDestination, weight, service level

The pattern that surprises buyers is that material is rarely the problem. A heat sink is mostly air by volume, but you pay for the solid block it starts as and for the time taken to turn that block into fins. Doubling the base thickness raises material cost modestly and machining time substantially.

The five variables that actually set the price

Fin count. Every additional fin is another set of passes with a small cutter. Going from eight fins to sixteen on the same footprint roughly doubles the finishing time, and the cutter has to be smaller, which means slower feed rates and more wear. This is the single largest lever in a heat sink quote.

Fin depth and aspect ratio. A deep, narrow gap needs a long, thin tool, and a long thin tool has to be run gently or it deflects and chatters. A 20 mm deep gap at 1.5 mm wide is a different machining proposition from a 6 mm deep gap at 3 mm wide. If the thermal design allows shallower fins with a wider base spreader, the quote usually falls faster than the performance does.

Base thickness and stock removal. A 12 mm base on a 60 x 60 mm footprint means removing a lot of aluminium around the fin field. Starting from plate closer to the finished base thickness, or designing a pocketed base, cuts roughing time directly.

Tolerance and flatness callouts. ±0.005 mm on critical features is standard at SkillsProto and is not what inflates a heat sink quote. A blanket flatness callout across the whole base, or a tight tolerance on a non-functional cosmetic face, does. Specify flatness where the thermal interface is and ISO 2768-m elsewhere.

Finish. As-machined is included in the machining time. Bead blast is minutes. Anodising is a batch process with a colour and thickness schedule, and masking areas that must stay conductive adds labour. If the part is going on a test bench this week, ask whether bare machined aluminium answers the thermal question first.

VariableEffect on costCheapest design change
Fin count 8 to 16Roughly doubles finishing timeKeep the fin count the thermal model needs, not the maximum that fits
Fin depth 6 to 20 mmTool L/D rises, feeds fallUse a thicker base to spread heat instead of deeper fins
Base 6 to 12 mmMore roughing, more materialStart from plate near net thickness
Blanket flatness 0.02 mmExtra setup and inspectionCall flatness only under the source footprint
Hard anodiseBatch queue plus maskingAs-machined or clear anodise for the prototype

Lead time by route

Lead time is a different question from cost and it is decided earlier, when you choose the process.

RouteLead time from released modelTooling neededSensible quantity
CNC machined from plate3-7 days, 48-hour expedite on simple geometryNone1-500
Machined from stock extrusion3-7 days plus profile availabilityNone if the profile is standard1-500
New extrusion dieWeeks for the die, then days per partDieThousands
Aluminium tooling, molded polymer parts7-10 days to T1 samplesAluminium mold100-10,000
Die cast metal heat sinkMold in 15-25 days, 500-piece minimumSteel mold500+
DDP delivery after production3-5 days to UK, EU and North AmericaNoneAny

Two things follow. First, if the design is not frozen, only machining makes sense, because a change costs a new model rather than a new die or mold. Second, the date on your desk is production plus transit: a 3-7 day machining window plus 3-5 days of DDP delivery is a two-week door-to-door expectation, and a plan built on the machining number alone slips by a week.

Cutting prototype cost without cutting thermal performance

The useful question is not "how do I make this cheaper" but "which cost is buying thermal performance and which is buying nothing".

  • Put the fins where the heat is. A machined heat sink does not need uniform fin density. Dense fins over the source and coarse fins elsewhere can remove as much as 40% of the fin count for the same thermal resistance, and fin count is the biggest cost line.
  • Spend on the base, not the fins. Spreading resistance dominates when the source is small relative to the base. A thicker base under the die, or a raised pedestal, often beats deeper fins for both performance and price.
  • Machine the interface, not the cosmetics. Flatness and roughness under the source footprint matter. The outside faces do not.
  • Prototype in the production alloy only if it is free. 6061-T6 machines well and conducts at roughly 167 W/m-K. If the production part will be 6063 extrusion at roughly 209 W/m-K, test the machined part in 6061 and treat the difference as a known margin rather than paying for a material trial.
  • Order three to five, not one. Once the machine is set up, extra parts add material and cycle time, not another queue. Five parts at prototype stage routinely prevent a second order two weeks later.

A worked comparison

Take three versions of the same 100 x 60 mm footprint at ten pieces, with a relative cost index rather than a quotation:

DesignFinsFin depthBaseRelative costNote
A: uniform dense fins1815 mm8 mm100Highest finishing time, best fin area
B: dense over source only1115 mm8 mm68Same thermal resistance in most models
C: fewer, deeper, thicker base1110 mm12 mm62Better spreading, cheaper to machine
D: A with hard anodise1815 mm8 mm118Adds finish queue and masking

The ranking is the point, not the numbers: fin count dominates, base thickness is cheap insurance, and a finish chosen for appearance can cost more than the design change that removed seven fins.

Getting a costed heat sink quote

Send the STEP file, the heat load and the airflow you expect, and the mounting pattern to /quote/. SkillsProto returns DFM notes and a price within 24 hours, machines from 6061, 7075, 6082 or copper to ±0.005 mm on critical features, ships MOQ 1 in 3-7 days with a 48-hour expedite where the geometry allows, and delivers DDP in 3-5 days. If an extrusion or a die casting is the better route at your volume, the quote will say so.

Frequently Asked Questions

How much does a heat sink prototype cost?

There is no single number because the quote is dominated by machining time, and machining time is set by fin count and fin depth rather than by size. A coarse-fin heat sink on a small footprint can cost a fraction of a dense-fin design on the same footprint. Send a STEP file and the price comes back in 24 hours with the cost drivers named.

Why did my heat sink quote come back higher than expected?

Usually one of three reasons: more fins than the thermal model needed, fins deep and narrow enough to force a long thin cutter and slow feeds, or a finish such as hard anodise added to a part that was going on a test bench. A blanket flatness callout across the whole base instead of under the source is the fourth common cause.

How long does a machined heat sink prototype take?

3-7 days from a released model, with a 48-hour expedite available on simple geometry. Add 3-5 days of DDP transit to the UK, EU or North America. If the part needs an anodised finish, add the finishing batch to the front of that window rather than assuming it happens inside it.

Is a cast heat sink cheaper than a machined one for prototypes?

No, at prototype quantity. A die cast heat sink needs a steel mold in 15-25 days and a 500-piece minimum, so the tooling is spread over far more parts than a prototype order contains. Die casting becomes the cheaper route only when the volume is there to absorb the mold.

Can I prototype a heat sink without paying for tooling?

Yes. Both CNC machining from plate and secondary machining of a stock extrusion involve no tooling at all, and MOQ is 1. Tooling only enters the picture when you commit to an extrusion die, an aluminium mold for a molded part or a die casting mold.

What tolerance should I call out on a heat sink?

±0.005 mm on critical features such as mounting hole positions and the thermal interface face, and ISO 2768-m for everything else. Flatness matters more than tolerance on the interface: specify it under the source footprint, where the thermal path is, rather than across the whole base.

Related capabilities

Related guides

Have parts to quote?

Upload your files — DFM-checked quotation within 24 hours.

見積もりを依頼